Brian & Brandi's RV-10

Lack of website updates


by Brian Wednesday, May 09, 2012

I hate it that I havent been keeping the site very up to date with details of the build. In this phase of the build its like 1,000 action items and a lot are small items that do not produce something thats photo/website worthy. Or perhaps its because we're so close to getting this thing flying we're just focused on building and not on pictures/website stuff. 

For consolation, here is my current to do list in order to give a glimpse of what I've been up to. Brandi has her own separate list, which includes mostly interior finishing. 

Time Estimate     To Do

0  Attach oil door

0  Nutplates on cowl front

0  Install Adahr rack

0  Install radio stack brackets

0  Wire SL40, 430, Audio Panel

0  Baffling

0  Run wires from audio panel to skyviews

0  Add an315-3r jam nuts to control cables

0  Drill vent holes in subpanel near fans

0  Run RS 232 TX from L. Skyview to ELT 

0  Install Panel

0  update skyview firmware

0  windscreen fairing

0  Filtered air box - apply black rtv + hookup air door cable

0  Test and check wiring system

0  Fire barrier on FWF

0  Run wiring from EMS to wing roots for fuel sensors

0  Trim air intake snoot

0  Fix R. front baffle

0  wire tie runs down side of fuse

0  Baggage light switch

0  Elevator Pushrod

0  Configure flap sensor - run wiring

0  430 bracket FWF - wait on tnc connector

0  anti-chafe tape on control cables

0  Seat rail mod - cut 3/8" off front rail umhw

0  Plug alt static air and determine final location

0  check xpdr wiring for 430 serial in - also add ident stick button?

0  Rear rudder cable fairings

0  Sand bottom cowl

0  Rear strobe

0  sand door area 

0  Section 11 - re-rivet L-bracket - wait on spruce order nas623

0  Battery Install - order

0  install elevator trim

0  ground misc to battery

 

0.25  Extract broken screw in cowl pin cover - find/buy replacement screw

1  Figure out elevator trim 

2  Section 11 - Empennage attach

1  Section 12 rudder fairing (strobe) attach + wiring

1  install ELT antenna - wait for horizontal stab attach

0.5  Torque Prop & safety - need special torq tool? what are torq values?

Attach Comm antenna - buy screws

Sand Wheel Fairings - defer until after flying? - replace some? 

0.5  cross check POH instrument markings lycoming documentation

0.5  bracket for battery - get some scrap aluminum from shop

2  Seat Belts install - create bushings - wait on brandi - buy 6mm washer?

1  strobe wiring run through wing conduit

Figure out mag wiring - buy slickstart booster?

1  Take wings off loft

0.5  Add roll servo stops - be mindful of short screws: http://www.vansairforce.com/community/showthread.php?t=70435

1  Run coax to bob-archer in R. wing 

3  J-Stiffener re-rivet on wing? 

2  5Attach wings - plan for Sat

2  Check stick clearance with elevator on - adjust elev linkage slightly?

0.5  Add wing walk

1  Check all fuel/oil lines torque and seal

1  Rivet tailcone top skin

0.25  Put Aeroshell #5 into grease fitting in caster nosewheel bearing

Scales - need to find some to use/rent

Seal firewall with 3m Firebarrier - use clay from Steve on wire bundles

Alternator - Belt + safety wire

split 430 serial between xpndr/696?

update aviation and obstacal db + skyview 3.3.2